Organic Syntheses

Part 1 out of 2








Scanned by Charles Keller with OmniPage Professional OCR software

TB is a triple bond. <.> is a dotted (coordinated) bond.
"Emphasis" _italics_ have a * mark.
[#] footnotes moved to EOParagraphs but NOT renumbered.
(They are numbered "a" or "b" when two pages of notes are together.)
Comments and guessed at characters in {braces} need stripped/fixed.
Greek letters are encoded in brackets, and the letters are
based on Adobe's Symbol font.





ORGANIC SYNTHESES

AN ANNUAL PUBLICATION OF SATISFACTORY METHODS FOR THE PREPARATION
OF ORGANIC CHEMICALS

_EDITORIAL BOARD_

JAMES BRYANT CONANT, _Editor-in-Chief_ HANS THACHER CLARKE ROGER
ADAMS OLIVER KAMM

_CONTRIBUTORS_ G. H. COLEMAN J, C. HESSLER E. P. KOHLER C. S. MARVEL
W. A. NOYES G. R. ROBERTSON E. B. VLIET F. C. WHITMORE

VOL. II.




Caveat: Some numbers did not OCR correctly and may not have been
corrected during the proofing! Check the 1941 print edition
before trying these!

INTRODUCTION TO THE SERIES


THE publication of this series of pamphlets has been undertaken
to make available in a permanent form complete detailed directions
for the preparation of various organic chemical reagents.
In announcing this purpose it may be well to mention at the outset
some of the difficulties in the way of the research chemist, which it
is hoped this series will be able to overcome. The cost of chemicals
is prohibitive to the majority of chemists; this was true before
the war when Kahlbaum's complete supply was available, and to-day
with our dependence on domestic stocks, this cost has increased.
The delay in obtaining chemicals, especially from abroad,
even if the expense need not be considered, is an important factor.
These difficulties have therefore thrown the research chemist on his
own resources. The preparation of materials for research, always time
consuming and annoying, is made increasingly so by the inexactness
of the published information which so often omits essential details.
Because of this, much needless experimentation is necessary
in order to obtain the results given in the published reports.
As the additional information thus acquired is seldom published,
duplication of such experiments occurs again and again,--
a waste of time and material. It is hoped these difficulties
may be remedied by the publication of this series of pamphlets.
In other words, the authors hope to make this a clearing house
for the exchange of information as to methods of preparation of some
of the most needed organic chemical reagents.

On account of the impossibility of obtaining the less common
organic chemicals in the United States during the past few years,
university laboratories have had no option but to prepare their
own supplies. At the University of Illinois, for instance,
a special study has been made of this field, and methods for
the production of various substances have been investigated.
As a result, reliable methods and directions have been developed
for producing the materials in one-half to five pound lots.
Such work as Illinois has done is now being given an even more extensive
scope at the Research Laboratory of the Eastman Kodak Company. It is
felt that the results from these various laboratories should be
available to all chemists and it is hoped that they eventually
will be completely incorporated in these pamphlets.

The organic chemicals herein discussed have been quite
arbitrarily chosen, being those which have been needed in various
research laboratories in the last years and for which the directions
happen now to be ready for publication. The methods are in only
a few cases new ones; they are in general the most satisfactory
to be found in the literature. Only such details have been added
as will enable a man with a reasonable amount of experience
in organic chemistry to duplicate the results without difficulty.
To be absolutely sure that each set of directions can be repeated,
every experiment has been carried out in at least two laboratories.
Only after exact duplication of the results in both laboratories
are the directions considered ready for publication.
The names of the chemists who have studied the various experiments
are given so that further information concerning any obscure point
can be obtained if any question arises in using these directions.
And finally, in describing the experiments, special attention has
been given to the explanation of why it is necessary to follow
the directions carefully, and what will happen if these directions
are not followed.

Although the main object in this series is to give the most convenient
laboratory methods for preparing various substances in one-half
to five pound lots, an attempt has also been made to have these
processes as far as possible adaptable to large scale development.
For example, extractions have been avoided wherever possible,
cheap solvents have been sub-stituted for expensive ones,
and mechanical agitation, a procedure extremely important in the
success of many commercial processes, has usually been specified.
The apparatus used is always carefully described and wherever necessary
an illustration is given. Accompanying each preparation there will
be found a bibliography containing references to all the methods
for the production of the substance described in the literature.
This is given in order to aid any future investigator who
may wish to study or improve the methods of preparation.
It is not claimed that the methods are, in every case,
completely perfect, but only that the yields are very satisfactory
and allow the production of the substances at a reasonable cost.
It is hoped therefore that the pamphlets will benefit not only
the scientific research man of the university, but also the
technical chemist who desires to develop the preparation of one
of these substances to a large scale process of manufacture.
The editors trust also that this work may be used to advantage
as a preparation manual in intermediate or advanced courses in
organic chemistry in university laboratories, and that it will aid
small colleges in the production of necessary reagents which they
are often financially unable to purchase.

The pamphlets are to be edited by the following committee:
Roger Adams, University of Illinois, Urbana, Illinois; J. B. Conant,
Harvard University, Cambridge, Massachusetts; H. T. Clarke, Eastman
Kodak Company, Rochester, New York; Oliver Kamm, Parke, Davis Company,
Detroit, Michigan; each to act for one year as editor-in-chief
and the other three to assist him as associate editors. A new number
of the series will appear annually, and every five years the data will
be rearranged, revised, corrected, and then published in book form.
The number of preparations to be completed yearly is not fixed.
There will be, it is certain, about twenty; and it is hoped,
as the interest is stimulated in this work, that this number may
increase considerably. The editors especially desire to solicit
contributions from other chemists, not only in this country but abroad.
Whenever a compound is thoroughly and extensively studied in
connection with some research, it is hoped that complete directions
for its preparation will be assembled and sent to the editor.
He will then have them checked and published in a subsequent number.
Directions for the preparation of substances already on the market
are needed to make this work complete and will be gladly accepted.

It will, of course, be recognized that an occasional mistake or omission
will inevitably be found in such a pamphlet as this which contains
so many references and formulae. The committee on publication will
therefore deem it a favor if they are notified when any such error
is discovered. It is hoped also that if any chemist knows a better
method for the preparation of any of the compounds considered,
or if anyone discovers any improvements in the methods, he will
furnish the authors with such information. Any points which may arise
in regard to the various preparations will be gladly discussed.
In conclusion, the editors are ready to do all they can to make this.
work successful, and welcome suggestions of any kind.
They feel that the success of the series will undoubtedly depend
upon the cooperation of others, and as its success promises to be
important to research chemists, the editors urge all interested
to assist. THE EDITORS



TABLE OF CONTENTS
PAGE
I. BENZALACETOPHENONE...........................1
II. BENZYL BENZOATE.............................5
III. BENZYL CYANIDE.............................9
IV. a, g-DICHLOROACETONE..............13
V. _p_-DIMETHYLAMINOBENZALDEHYDE..................17
VI. ETHYL OXALATE...............................23
VII. ETHYL PHENYLACETATE........................27
VIII. GLYCEROL a, g-DICHLOROHYDRIN....29
IX. GLYCEROL a-MONOCHLORORYDRIN............33
X. HYDRAZINE SULFATE............................37
XI. MESITYLENE..................................41
XII. METHYL RED.................................47
XIII. _p_-NITROBENZOIC ACID.......................53
XIV. _p_-NITROBENZYL CYAI~DE......................57
XV. _p_-NITROPHENYLACETIC ACID....................59
XVI. NITROSO-b-NAPHTHOL....................61
XVII. PHENYLACETIC ACID.........................63
XVIII. PHENYLACETYLENE..........................67
XIX. PHENYLHYDRAZINE............................71
XX. PHTHALIMIDE.................................75
XXI. QUINOLINE..................................79
XXII. QUINONE...................................85
XXIII. SODIUM _p_-TOLUENESULFINATE................89
XXIV. 1,3,5-TRINTROBENZENE......................93
XXV. 2,4,6-TRINTROBENZOIC ACID..................95
INDEX.....................................99



ORGANIC SYNTHESES

I

BENZALACETOPHENONE

C6H5CHO + C6H5COCH3 + (NaOH)--> C6H5CH=CHCOC6H5 + H2O

Prepared by E. P. KOHLER and E. M. CHADWELL. Checked by H. T. CLARKE
and R. P. LEAVITT.

1. Procedure

A SOLUTION of 218 g. of sodium hydroxide in 1960 g.
of water and 1000 g. of 95 per cent alcohol are introduced into
a 5500-cc. bottle which is loosely covered with a perforated disk
of cardboard, supplied with an effective stirrer, and supported
in a larger vessel so as to permit cooling with cracked ice.
Into the alkaline solution, 520 g. of pure acetophenone is poured,
the bottle is rapidly surrounded with cracked ice, and the stirrer started;
460 g. of benzaldehyde (U. S. P.) are then added at once.
The temperature of the mixture should not be below 15'0 and it
should not be allowed to rise above 30'0 during the reaction.
If it tends to do so, the stirring is not sufficiently vigorous.

It is advantageous, though not essential, to inoculate the mixture
with a little powdered benzalacetophenone after stirring for half
an hour. After two to three hours, the mixture becomes so thick
that the stirring is no longer effective. The stirrer is then
removed and the mixture left to itself in an ice-box for about
ten hours. The mixture now is a thick paste composed of small
shot-like grains suspended in an almost colorless liquid.
It is cooled in a freezing mixture and then either centrifuged
or filtered on a large Buchner funnel, washed with water until
the washings are neutral to litmus, and finally washed with 200 cc.
of alcohol, which has previously been cooled to 0'0. After
thorough drying in the air, the crude product weighs about 880 g.
(yield 97 per cent of the theoretical amount) and melts at 50-54'0.
It is sufficiently pure for most purposes but tenaciously holds
traces of water. It is most readily purified by recrystallization
from four to four and a half times its weight of 95 per cent alcohol.
Eight hundred and eighty grams of crude product give 770 g.
(85 per cent of the theoretical amount) of light-yellow material
(m. p. 55-57'0) and 40-50 g. that require recrystallization.

2. Notes

The acetophenone should be as pure as possible (m. p.
20'0). Commercial acetophenone contains variable quantities of impurities
which reduce the yield. By distilling commercial acetophenone with
the help of a good still-head (preferably under diminished pressure)
and using only the fraction which boils at 201-202'0 (76-77'0/10 mm.)
greater quantities of benzalacetophenone can be obtained than by using
the entire sample.

Commercial benzaldehyde can be used in place of the purer product,
but the amount used must be increased to make up for the impurities
which are present.

If the temperature is too low, or the stirring too slow, the product
separates as an oil, which later solidifies in large lumps.

If the temperature is allowed to rise above 30'0, secondary
reactions diminish both the yield and the purity of the product.
The most favorable temperature is 25'0.

In recrystallizing benzalacetophenone, the alcohol should be saturated
at 50'0. If the solution is saturated above this temperature,
the benzalacetophenone tends to separate as an oil. The solution
should be allowed to cool gradually, and should finally be chilled
in a freezing mixture. 3. Other Methods of Preparation

The methods for producing benzalacetophenone are: the action of acids
on a mixture of benzaldehyde and acetophenone or on a solution
of these substances in glacial acetic acid;[1] the condensation
of benzaldehyde and acetophenone with a 30 per cent solution of sodium
methylate at low temperatures;[2] the action of sodium hydroxide
on an alcoholic solution of benzaldehyde and acetophenone.[3]

The methods based on the use of acids as condensing agents were
not considered, because Claisen, who devised them, abandoned them
after he found that alkaline condensing agents gave better results.
The preliminary experiments showed that condensation with sodium
methylate takes a long time and gives a product which it is difficult
to handle in large quantities. The method devised by Kostanecki
and Rossbach[3] has therefore been developed.

[1] Ber. 14, 2463 (1881).

[2] Ber. 20, 657 (1887).

[3] Ber. 29, 1492 (1896).



II

BENZYL BENZOATE

2 C6H5CHO + C6H5CH2ONa--> C6H5CO2CH2C6H5 + C6H5CH2ONa

Prepared by O. KAMM and W. F. KAMM. Checked by ROGER ADAMS and
R. L. JENKINS.

1. Procedure

THREE grams of metallic sodium are dissolved by warming for half an hour
in 70 g. of pure benzyl alcohol (see notes), and after the mixture
has cooled to room temperature the solution is added gradually,
with thorough mixing, to 454 g. of c. p. benzaldehyde (which must
contain LESS than 1 per cent of benzoic acid). The reaction mixture has
a tendency to become warm, but the temperature should be kept slightly
below 50-60'0 by cooling, if necessary. A pasty gelatinous mass results.
After about half an hour the temperature of the mixture no longer rises;
it is then warmed on the water bath for about one or two hours,
with occasional shaking.

The cooled reaction product is treated with 200 cc.
of water, the layer of oil separated, washed once with a second
portion of water, and subjected to distillation _in vacuo_.
The first fraction of the distillate contains benzyl alcohol together
with unchanged aldehyde, as well as a small quantity of water.
The temperature then rises rapidly to the boiling-point of
benzyl benzoate, when the receivers are changed. The product
boils at 184-185'0/15 mm., and analysis by saponification shows it
to consist of 99 per cent ester. A yield of 410-420 g. is obtained,
which corresponds to 90-93 per cent of the theoretical amount.
This benzyl benzoate supercools readily, but after solidifying
melts within one degree of the highest recorded value (19.4'0) and
therefore need not be refractionated, unless material of exceptional
grade is required.

2. Notes

In the presence of sodium benzylate two molecules of benzaldehyde
react with the alcoholate to form an addition product.
When the reaction mixture is overheated an important side reaction
may occur, as follows:

/ OCH2C6H5
C6H5C -- OCH2C6H5 --> C6H5CO2Na + C6H5CH2OCH2C6H5
\ ONa

Dibenzyl ether no doubt forms the chief impurity in benzyl benzoate.
Since the boiling-point of the former lies near that of the ester,
it is not removed during the process of purification by distillation.

The causes of variations in yield by the use of the older methods
can now be explained. When benzaldehyde is added TO THE ALCOHOLATE,
and especially when the latter is still warm, local overheating results;
in fact, the temperature may rise far above 100'0 with the result
that benzyl ether is formed. Simultaneously, the sodium benzylate
is converted into sodium benzoate, which is of no value for inducing
the desired reaction, and consequently very little benzyl benzoate
is obtained. The same side reactions explain the failure of this
experiment when the benzyl alcohol used in preparing the catalyst
(sodium benzylate) is contaminated with benzaldehyde.

The benzyl alcohol used in this preparation must be free
from impurities, especially aldehyde. One cc. dissolved in 50 cc.
of water and treated with a freshly prepared clear solution of
phenylhydrazine acetate should give no appreciable precipitate.
If it is not pure, it must first be treated with alkali
as described below.

The benzaldehyde should be titrated in order to determine its acidity.
If it is found to contain sufficient benzoic acid to react
with a considerable proportion of the sodium alcoholate, a poor
yield of ester will be obtained. Less than 1 per cent of benzoic
acid will not interfere seriously with the yields obtained,
but the presence of larger quantities of acid will be found to be
detrimental and must be removed by washing the benzaldehyde with
a sodium carbonate solution and redistilling with the precautions
necessary to prevent too free an access of air to the distillate.

The order of mixing the reagents and the temperature of the ingredients
at the time of mixing are the most important factors in the experiment.
The temperature at which the reaction mixture is maintained
after mixing, provided that it is held below 100'0, is less important
from the standpoint of purity.

The reaction mixture is not treated with acetic acid, as usually
recommended, for the reason that such a procedure yields a final
product contaminated with benzoic acid, unless an alkaline wash
is applied subsequently.

The recovered benzyl alcohol can be used for the preparation
of a second lot of benzyl benzoate only after it has been boiled
with strong sodium hydroxide to remove all traces of benzaldehyde.


3. Other Methods of Preparation

Benzyl benzoate has been identified in certain natural plant
products.[1] In the laboratory it has been prepared by the action of
(_a_) benzoyl chloride upon benzyl alcohol,[2] (_b_) benzyl chloride
upon sodium benzoate, and (_c_) alcoholates upon benzaldehyde.[3]
Recently, Gomberg and Buchler[4] have shown that reaction (_b_) may
be conducted even with aqueous solutions of sodium benzoate.


[1] Ann. 152, 131 (1869).

[2] Gmelin's Handbuch der Organ. Chem. 3, 40.

[3] Ber. 20, 649 (1887). Cf. also J. Chem. Soc. 75, 1155 (1899).

[4] J. Am Chem. Soc. 42, 2059 (1920).


The Claisen method (_c_) furnishes the most convenient and practical
procedure for the preparation of this ester. The materials are cheap,
the experimental procedure simple, and the product obtained is free
from objectionable traces of benzyl chloride. Unfortunately the
method has been found to be extremely erratic in regard to yield
(10-95 per cent), as well as in regard to purity of the product
(87-97 per cent ester).[1] As a result of the present study,[2]
causes for variations are fully accounted for and the procedure
has been converted into a satisfactory method of preparation.


[1] C. A. 14, 3500 (1920).

[2] J. Am. Pharm. Assoc. 11, 599 (1922).



III

BENZYL CYANIDE

C6H5CH2Cl + NaCN--> C6H5CH2CN + NaCl

Prepared by ROGER ADAMS and A. F. THAL Checked by O. KAMM and
A. O. MATTHEWS.

1. Procedure

IN a 5-l. round-bottom flask, fitted with a stopper holding
a reflux condenser and separatory funnel, are placed 500 g.
of powdered sodium cyanide (96-98 per cent pure) and 450 cc.
of water. The mixture is warmed on a water bath in order
to dissolve most of the sodium cyanide, and then 1 kg.
of benzyl chloride (b. p. 170-180'0) mixed with 1 kg.
of alcohol is run in through the separatory funnel in the course
of one-half to three-quarters of an hour. The mixture is then
heated with a reflux condenser on the steam bath for four hours,
cooled and filtered with suction to remove most of the sodium chloride.
It is well to wash the filtered salt with a small portion of
alcohol in order to remove any benzyl cyanide which may have been
mechanically held. The flask is now fitted with a condenser,
and as much alcohol as possible is distilled off on the steam bath.
The residual liquid is cooled, filtered if necessary, and the layer
of benzyl cyanide separated. This crude benzyl cyanide is now
placed in a Claisen distilling flask and distilled _in vacuo_,
the water and alcohol coming over first, and finally the cyanide.
It is advantageous to use a fractionating column or, better still,
a Claisen flask with a modified side-arm[1] (Vol. I, p.
40, Fig. 3) which gives the same effect as a fractionating column.
The material is collected from 135-140'0/38 mm. (115-120'0/10 mm.).
The yield is 740-830 g. (80-90 per cent of the theoretical amount).

[1] J. Am. Chem. Soc. 39, 2718 (1917). 2. Notes

The quality of the benzyl chloride markedly affects the yield
of pure benzyl cyanide. If a poor technical grade is used,
the yields will not be more than 60-75 per cent of the theoretical,
whereas consistent results of about 85 per cent or more were always
obtained when a product was used that boiled over 10'0. The technical
benzyl chloride at hand yielded on distillation about 8 per cent
of high-boiling material; a technical grade from another source was
of unusual purity and boiled over a 2'0 range for the most part.

It is advisable to distil off the last portion of alcohol and water
_in vacuo_ and also to distil the benzyl cyanide _in vacuo_,
since under ordinary pressures a white solid invariably separates
during the distillation.

One method of purifying the benzyl cyanide is to steam distil it
after the alcohol has been first distilled from the reaction mixture.
At ordinary pressures, this steam distillation is very slow and,
with an ordinary condenser, requires eighteen to twenty hours
in order to remove all of the volatile product from a run of 500 g.
of benzyl chloride. The distillate separates into two layers; the benzyl
cyanide layer is removed and distilled. The product obtained in this
way is very pure and contains no tarry material, and, after the excess
of benzyl chloride has been removed, boils practically constant.
This steam distillation is hardly advisable in the laboratory.

The benzyl cyanide, prepared according to the procedure as outlined,
is collected over a 5'0 range. It varies in appearance
from a colorless to a straw-colored liquid and often develops
appreciable color upon standing. For a product of special purity,
it should be redistilled under diminished pressure and collected
over a 1-2'0 range. For most purposes, such as the preparation
of phenylacetic acid or ester, the fraction boiling 135-140'0/38 mm.
is perfectly satisfactory. 3. Other Methods of Preparation

Benzyl cyanide occurs naturally in certain oils.[1] The only feasible
method of preparing it that has been described in the literature is
the one in which alcoholic potassium cyanide and benzyl chloride[2]
are employed. The cheaper sodium cyanide is just as satisfactory
as the potassium cyanide and therefore is the best material to use.
Gomberg has recently prepared benzyl cyanide from benzyl chloride
and an aqueous solution of sodium cyanide.[3]


[1] Ber. 7, 519, 1293 (1874); 32, 2337 (1899)

[2] Ann. 96, 247 (1855); Ber. 3, 198 (1870); 14, 1645
(1881); 19, 1950 (1886).

[3] J. Am. Chem. Soc. 42, 2059 (1920).



IV

a, g-DICHLOROACETONE

CH2ClCHOHCH2Cl + O(Na2Cr2O7 + H2SO4)--> CH2ClCOCH2Cl + H2O

Prepared by J. B. CONANT and O. R. QUAYLE. Checked by A. W. DOX, L. YODER,
and O. KAMM.

1. Procedure

IN a 2-l. flask are placed 375 g. of commercial sodium dichromate,
225 cc. of water, and 300 g. of dichlorohydrin (b. p.
68-75'0/14 mm.). The flask is set in a water bath and equipped
with a thermometer and mechanical stirrer. The contents are
vigorously stirred, and 450 g. of sulfuric acid, diluted with 115 g.
of water, are introduced during the course of seven to eight hours.
It is convenient to add the acid at ten-minute intervals.
The temperature is kept between 20'0 and 25'0 during the entire reaction;
this is accomplished by adding a little ice to the water bath from
time to time. The stirring is continued for sixteen to seventeen
hours after all the acid has been added; as there is very little
heat evolved during this part of the reaction, the water bath may
be allowed to come to room temperature.

Sufficient water is now added to the mixture to dissolve the pasty
chromium salts (300-800 cc.). The mass of crystals is then rapidly
filtered on a Buchner funnel and sucked as dry as possible.
The crystals are then transferred to a small laboratory centrifuge
and centrifuged for several minutes. The crystals are washed in
the centrifuge with about 15-25 cc. of ice water, then with 10-15 cc.
of cold petroleum ether, and finally centrifuged till as dry as possible.
The crude dichloroacetone is dried in a vacuum desiccator over
sulfuric acid overnight It weighs about 220 g.

The crude product is best purified by distillation from
a 250-cc. distilling flask fitted with an air condenser.
A very small fraction (10-15 g.) of low-boiling material is obtained,
and the dichloroacetone (170-175'0) is then collected. It solidifies
in the receiver to a white crystalline mass which weighs 200-220 g.
(65-70 per cent of the theoretical amount). A few grams more may
be obtained by chilling the low-boiling fraction and filtering
off the water.


2. Notes

Great caution should be exercised in working with dichloroacetone,
as it is extremely lachrymatory and blisters the skin.

In transferring the crystals from the reaction flask to the Buchner
funnel it is necessary to use a certain amount of water to dissolve
the pasty chromium salts which are otherwise quite impossible
to filter. The amount necessary varies greatly in different runs,
according to the manner in which the chromium salts separate.
The amount of this water is kept low in order to dissolve
as little of the product as possible. Nevertheless, 10-15 g.
of dichloroacetone are thus dissolved; this material, together with
a little unchanged dichlorohydrin, may be recovered by a long
procedure involving extraction with ether and sodium bisulfite.
This is not profitable, however.

It is not necessary to wash the crystals in the centrifuge until
they are white. A small amount of chromic salt will not interfere
with the subsequent purification.

Commercial sodium dichromate is hygroscopic and contains varying
amounts of water. The 375 g. required in these directions are
equivalent to 319 g. of anhydrous material.

The total time required for the oxidation is twenty-four hours.
It is convenient to start the reaction in the morning.
In this way the last part of the reaction, which requires
no attention, will be accomplished during the night.
The regulation of the temperature is necessary, as the reaction
proceeds very slowly below 20'0; on the other hand, the dichloroacetone
itself is oxidized at a somewhat higher temperature than 25'0. 3.
Other Methods of Preparation

The preparation of dichloroacetone by the following methods
is described in the literature: the direct chlorination of
acetone;[1] the oxidation of dichlorohydrin;[2] the action of silver
chloride on diiodoacetone;[3] the action of dichloropropene
(CH2Cl-CCl=CH2) and hypochlorous acid;[4] the action of hydrochloric
acid on ethoxymonochloroacetoacetic ester;[5] and the hydrolytic
cleavage of dichloroacetoacetic ester.[6]


[1] Jahresb. 1859, 345; 1871, 531; J. prakt. Chem. (2)4, 52
(1871); Ber. 7, 467 (1874); 8, 1330, 1438 (1875); 26, 598
(1893); 42, 3233 (1909); Ann. 279, 315 (1894)

[2] Ber. 6, 1210 (1873); 13, 1706 (1880); 42, 3233 (1909); Ann.
208, 355 (1881); 269, 46 (1892); Ann. chim. phys. (6) 9, 145
(1886); Bull. soc. chim. (2) 36, 19 (1881).

[3] Ann. 192, 93 (1878).

[4] Compt. rend. 94, 1428 (1882).

[5] Ann. 269, 18 (1892).

[6] Ber. 43, 3533 (1910).




V

_p_-DIMETHYLAMINOBENZALDEHYDE

(CH3)2NC6H5 + HNO2--> (CH3)2NC6H4NO + H2O (CH3)2NC6H4NO + 2HCHO
+ 2C6H5N(CH3)2 --> (CH3)2NC6H4N
= CHC6H4N(CH3)2 + 2H2) + (CH3)2NC6H4CHO
(CH3)2NC6H4N = CHC6H4N(CH3)2 + HCHO-->( CH3)2NC6H4N = CH2 + (CH3)2NC6H4CHO

Prepared by ROGER ADAMS and G. H. COLEMAN. Checked by H. T. CLARKE
and W. W. HARTMAN.

1. Procedure

IN a 3-l. round-bottom flask fitted with a mechanical stirrer 150 g.
of technical dimethylaniline are dissolved in 750 cc.
of diluted hydrochloric acid (1 part concentrated acid to 1
part water). This solution is now cooled to 0'0 and a solution
(previously cooled to 0'0) of 90 g. of technical sodium nitrite
in 150 cc. of water is added through a separatory funnel.
During the addition of the nitrite solution, mechanical stirring
should be employed and the flask cooled well with ice and salt.
The addition is made at such a rate (thirty to forty minutes
for the entire addition) that the temperature does not rise above
5'0. The precipitate of nitroso dimethylaniline hydrochloride
is filtered off with suction, then washed with about 300 cc.
of diluted hydrochloric acid (1:1).

In a 2-l. beaker, 180 g. of technical dimethylaniline, 125 cc.
of formaldehyde (technical 40 per cent), and 300 cc.
of concentrated hydrochloric acid are mixed and heated for ten
minutes on a steam bath. The mixture is now placed in a hood
and the nitroso dimethylaniline added all at once, or as rapidly
as possible. The beaker is then covered with a watch glass.
A vigorous reaction soon occurs and is complete in about five minutes.
The resulting solution is transferred to a 5-l. flask and diluted
to 4 l.; stirring is started, and a 25 per cent solution of sodium
hydroxide is added until the red color disappears (about 650 cc.
are required). The yellow benzylidene compound separates,
is filtered with suction and washed with water. The moist precipitate
is transferred to a 4-l. glass jar, covered with 1000 cc.
of 50 per cent acetic acid and 250 cc. of formaldehyde,
and stirred until twenty minutes after the benzylidene compound has
gone into solution. While the mixture is being stirred vigorously
to prevent lumping of the precipitate, 400 cc. of water and 200 g.
of cracked ice are added during the course of five minutes.
The dimethylaminobenzaldehyde generally separates gradually
in fifteen to twenty minutes, but in some cases does not.
If the precipitate does not form, the solution is placed
in a refrigerator for a few hours or overnight. The mixture is
filtered with suction and washed at least ten times with 300 cc.
of water. The precipitate is sucked as dry as possible for fifteen
to thirty minutes.

The slightly moist aldehyde is distilled under diminished
pressure from an oil bath, by means of a 1-l. Claisen flask.
A small amount of water comes over first, then the thermometer
rises rapidly to the boiling point of the aldehyde (180'0/22 mm.).
In changing receivers between the water fraction and the aldehyde,
care should be taken to keep the side-arm of the distilling
flask warm; otherwise, on starting the distillation again,
the aldehyde will solidify in the side-arm and cause trouble.
It is advisable not to collect the very last portion of the distillate
with the main portion, as the former is frequently quite red.
This is best added to crude material from another run. The main
distillate is dissolved in 100 cc. of alcohol in a 2-l. beaker,
then 1000 cc. of water are gradually added with vigorous mechanical
stirring to prevent lumping. The aldehyde separates, and is
filtered with suction. The product, when dry, weighs 125-130 g.
(56-59 per cent of the theoretical amount), and melts at 73'0.

The aldehyde prepared in this way is in the form of small
granular crystals, which vary in different runs from a flesh color
to a lemon yellow. For practically all purposes, this slightly
colored product is entirely satisfactory and is essentially pure,
as can be judged by the melting point. For reagent purposes it
is desirable to remove the color completely, particularly since
the product obtained as just described has a tendency to take
on a reddish tinge on exposure to light. Further purification can
be accomplished by dissolving the aldehyde (it dissolves slowly)
in dilute hydrochloric acid (1 part of concentrated acid, sp. gr.
1.19, to 6 parts of water), 125 g. of aldehyde requiring 700 cc.
of the acid. The solution is placed in a jar and diluted with
half its volume of water, and dilute sodium hydroxide solution
(15-20 per cent) is added slowly with mechanical stirring.
At the beginning, the aldehyde comes down slightly colored.
After about 10 to 30 g. are precipitated, however, the product
appears white; this point can be readily seen. The first precipitate
is filtered off and added to the next run of crude material,
or fractionally precipitated again from hydrochloric acid.
The rest of the aldehyde is now precipitated by means of more sodium
hydroxide solution, and comes down almost white. At the very end of
the neutralization, particularly if the original product was quite yellow,
the last 4 to 5 g. of aldehyde should be precipitated separately,
as they are inclined to be slightly colored. If too much alkali is
added towards the end of the neutralization, a brown color appears,
but the addition of a little hydrochloric acid will destroy this color.
The main portion of the precipitate is filtered and dried; it weighs
95-100 g., m. p. 73'0. The succeeding runs yield 115-128 g.
of finished product, on account of the extra crude material obtained
from the distillation and reprecipitation of the previous run. 2. Notes

The aldehyde that is obtained without reprecipitation
gradually takes on a pinkish tinge on exposure to light.
After the reprecipitation, however, this characteristic disappears.

Thorough washing of the crude aldehyde is particularly desirable,
as it removes a reddish impurity which tends to distil over and
color the product lemon yellow or sometimes even brownish yellow.
When such a brownish product is obtained, it is quite necessary to make
a second precipitation, as well as to observe the directions mentioned
in the purification of the crude aldehyde, namely, to precipitate
the first few grams and the last few grams of the aldehyde separately.
The precaution of rejecting the first and last portions
of the precipitate is unnecessary in the reprecipitation.
In the reprecipitation of a deeply colored product, the portion
of aldehyde at the end may be even purplish in color and particular
care must be taken to keep this separate.

Vigorous mechanical stirring must be employed during the precipitation
of the crude aldehyde, as otherwise large lumps are formed which
make washing difficult.

A previous investigator has mentioned that the crude product must
be dried before distilling. This, however, is unnecessary.
If the aldehyde is dried before distilling, it is possible to use
a 500-cc. distilling flask instead of a 1-l one.

In purifying the aldehyde by dissolving in acid and reprecipitating,
it is essential not to use stronger acid than that specified
(1:6), as stronger acid causes a deepening of the color of the solution.
If the concentrated acid, which is to be diluted and used in this
procedure, does not have a sp. gr. of 1.19, it will be necessary
to add the equivalent amount of weaker acid in order to dissolve
the _p_-dimethylaminobenzaldehyde. In purifying the aldehyde,
sodium carbonate may be used in place of sodium hydroxide
for precipitation, but it causes much foaming.

When the apparatus for distilling, etc., is all set up,
a run such as described above requires about five to six hours
for completion. 3. Other Methods of Preparation

_p_-Dimethylaminobenzaldehyde has been made by the condensation
of chloral with dimethylaniline, and subsequent hydrolysis;[1]
by the hydrolysis of tetramethyldiaminobenzhydrol with acetic
acid;[2] by the condensation of dimethylaniline, formaldehyde and
_m_-sulfo-_p_-tolyl hydroxylamine followed by hydrolysis;[3] by the
electrolytic reduction of a mixture of sodium nitrobenzene sulfonate,
dimethylaniline and formaldehyde, and subsequent hydrolysis;[4]
by the reduction of a mixture of dimethylaniline, formaldehyde and
sodium nitrobenzene sulfonate with iron and hydrochloric acid,
followed by hydrolysis;[5] by the condensation of alloxan with
dimethylaniline followed by hydrolysis;[6] by the condensation
of dimethylaniline, formaldehyde and sodium _p_-toluidine sulfonate
in the presence of hydrochloric acid and potassium dichromate
followed by hydrolysis.[7] The most satisfactory method, however,
is the condensation of dimethylaniline, formaldehyde and nitroso
dimethy]aniline, followed by hydrolysis,[8] a method which was first
described by E. Noelting and later perfected in detail by L. Baumann.


[1] Ber. 18, 1519 (1885); 19, 366 (1886); D. R. P. 61, 551; Frdl.
3, 109 (1892).

[2] Ber. 27, 3317 (1894).

[3] D. R. P. 103,578; Frdl. 5, 101 (1899).

[4] D. R. P. 105,103; Frdl. 5, 107 (1899).

[5] D. R. P. 105,105; Frdl. 5, 109 (1899).

[6] D. R. P. 108,086; Frdl. 5, 117 (1899).

[7] D. R. P. 118,567; Frdl. 6, 133 (1901).

[8] Ber. 37, 858 (1904); J. Biol. Chem. 41, 146 (1920).



VI

ETHYL OXALATE

(CO2H)2 + 2 C2H5OH--> (CO2C2H5)2 + 2H2O

Prepared by H. T. CLARKE and ANNE W. DAVIS. Checked by ROGER ADAMS
and W. B. BURNETT.

1. Procedure


IN a 5-l. flask are placed 1 kg. of crystallized (hydrated) oxalic
acid, 1.66 kg. of 95 per cent ethyl alcohol, and 1.33 kg.
of carbon tetrachloride. The flask is then fitted with a fractionating
column, I meter long, to which is attached a condenser and an automatic
separator so arranged that the lighter liquid flows off to a receiver
(Fig. 1). The heavier liquid flows through a tower of anhydrous
potassium carbonate, and then returns to the reaction flask.
The bottom of the tower is connected with a small separatory funnel
through which any potassium carbonate solution, which flows from
the solid in the tower, may be withdrawn from time to time.

The mixture in the flask is slowly distilled. As soon as about 500 cc.
of the lighter liquid has collected, it is placed in a fractionating
apparatus and distilled, the material which boils up to 79'0 being
collected separately. This fraction, which consists principally
of alcohol, with a little carbon tetrachloride and moisture, is dried
with potassium carbonate and returned to the reaction mixture.
The higher fractions are redistilled.

The above process is continued until the distillate no longer separates
into two phases (about twenty-seven hours). The liquid in the flask
is then distilled with the use of a column until the temperature
of the vapor reaches 85'0; the residue is then distilled under
reduced pressure, and the fraction which boils at 106-107/25 mm.
is collected. The yield is 920-960 g. of a colorless liquid
(80-84 per cent of the theoretical amount).


2. Notes

Water, ethyl alcohol and carbon tetrachloride form a ternary
mixture boiling at about 61'0. This vapor mixture, on condensation,
separates into two phases; the heavier liquid consists of carbon
tetrachloride and alcohol with only small amounts of water;
the lighter liquid consists of approximately 65 per cent alcohol,
25 per cent water and 10 per cent carbon tetrachloride.
By taking advantage of this fact, it is possible to conduct
the esterification at a temperature so low that the ethyl hydrogen
oxalate first formed does not decompose into ethyl formate
and other products, as is the case when the customary methods
of esterification are employed.

The reaction may be carried out somewhat more expeditiously
if the oxalic acid be dehydrated independently before it is mixed
with the alcohol; indeed, it is also possible to remove the bulk
of the water from the alcohol itself by a similar method, before mixing
it with the oxalic acid. However, since water is formed during
the esterification, little is gained by this procedure.

It is not absolutely necessary to remove the last traces of water from
the alcohol-carbon tetrachloride layer by means of potassium carbonate
before returning it to the reaction mixture; this process is, however,
so simple and requires so little attention that there is no doubt
that it is of material aid in cutting down the time of operation.
The advantages of using crystallized oxalic acid and commercial 95
per cent alcohol, instead of the anhydrous reagents, are obvious.
When technical oxalic acid is used, the yields are usually smaller
by 5 to 10 per cent.

The apparatus shown in Fig. 1 may be somewhat more simply constructed
by using rubber connections in several places, thus eliminating a certain
amount of glass blowing, and making a more flexible piece of apparatus.
The side-arm of the separator may be made with two rubber connections,--
one above and one below the tube leading to the potassium carbonate tube.
The long return tube to the flask may be constructed with a rubber
joint very near the carbonate tube and one near the flask.


3. Other Methods of Preparation

Ethyl oxalate has been prepared in poor yields by the following methods:
by distilling a mixture of anhydrous oxalic acid and absolute
alcohol;[1] by heating a mixture of anhydrous oxalic acid and 97 per
cent alcohol under a reflux condenser and fractionating the resulting
mixture;[2] by distilling a mixture of anhydrous oxalic acid
and absolute alcohol, the vapor of absolute alcohol being passed
simultaneously into the mixture;[3] by allowing a saturated solution
of oxalic acid in alcohol to stand for a long time at 40-50'0.[4]

A good yield has been obtained by Anschutz[5] by a method involving
saturation of a mixture of crystallized oxalic acid and alcohol
with hydrogen chloride, removal of the alcohol and water by
distillation under reduced pressure, and repetition of the treatment
with the alcohol and hydrogen chloride, the process being carried
out several times.


[1] Jahresb. 1861, 598.

[2] J prakt. Chem. (2), 34, 500 (1886).

[3] Monatsh. 17, 614 (1896).

[4] Ann. 65, 350 (1848).

[5] Ber. 16, 2414 (1883),



VII

ETHYL PHENYLACETATE

C6H5CH2CN + C2H5OH + H2SO4 + H2O--> C6H5CH2CO2C2H5 + NH4HSO4

Prepared by ROGER ADAMS and A. F. THAL. Checked by OLIVER KAMM.

1. Procedure

IN a 3-l. round-bottom flask, fitted with an efficient
reflux condenser, are mixed 750 g. of 95 per cent alcohol, 750 g.
of concentrated sulfuric acid and 450 g. of benzyl cyanide.
The mixture, which soon separates into two layers, is heated
to boiling over a low flame, for six to seven hours, cooled and
poured into 2 l. of water, and the upper layer is separated.
This is washed with a little 10 per cent sodium carbonate solution
to remove small amounts of phenylacetic acid which may have been formed,
and then distilled _in vacuo_. A small amount of water goes
over first and then a pure product boiling 132-138'0/32 mm.
(120-125'0/17-18 mm.). The yield varies in general between 525 and 550 g.
(83-87 per cent of the theoretical amount).


2. Notes

The benzyl cyanide can be most conveniently prepared according
to the directions in preparation III (p. 9); the product which boils
over a 5'0 range should be used.

In washing the layer of ethyl phenylacetate with sodium carbonate it
is sometimes advisable to add a certain amount of sodium chloride
so that the ester will separate more readily.

The product obtained is water-clear and practically colorless.
Although the product is collected over a 5'0 range, most of
the liquid is found to boil over a 1'0 range, if distilled
slowly without superheating.

The boiling point of ethyl phenylacetate is near that of benzyl cyanide.
However, a Kjeldahl analysis of the product shows that only a trace
of nitrogen compounds is present.


3. Other Methods of Preparation

Ethyl phenylacetate may be prepared by the treatment of benzyl
cyanide with alcohol and hydrochloric acid gas.[1] It is much more
convenient in the laboratory, however, to use sulfuric acid in place
of hydrochloric acid; in fact, the yields obtained are better
than those recorded in the literature. This ester may also be
made by the esterification of phenylacetic acid with hydrochloric
acid and alcohol;[2] or with alcohol and sulfuric acid;[3]
the following less important methods of preparation may be mentioned;
the action of benzyl magnesium chloride upon ethyl chlorocarbonate,[4]
and the action of copper on a mixture of bromobenzene and ethyl
chloroacetate at 180'0.[5]


[1] Ber. 20, 592 (1887); Ann. 296, 361 (1897)

[2] Ber. 2, 208 (1869).

[3] Ann. 296, 2, footnote (1897); Compt. rend. 152, 1855 (1911).

[4] Ber. 36, 3088 (1903).

[5] Ber. 2, 738 (1869).



VIII

GLYCEROL a, g-DICHLOROHYDRIN

C3H5(OH)3 + 2HCl--> CH2ClCHOHCH2Cl + 2H2O

Prepared by J. B. CONANT and O. R. QUAYLE. Checked by O. KAMM
and A. O. MATTHEWS.


1. Procedure

ONE kilo of 90 per cent glycerol (sp. gr. 1.243) and 20 g.
of acetic acid are placed in a weighed 2-l. flask which is immersed
in an oil bath heated to 100-110'0. The flask is fitted with a
two-hole stopper, which carries a long tube reaching to the bottom
of the flask and a short exit tube. The former is connected
to a hydrogen chloride generator, the latter to a catch-bottle
and some system for absorbing any excess of hydrogen chloride.
A stream of dry hydrogen chloride is passed into the mixture.
The absorption of gas is very rapid at the start, but gradually
falls off towards the end of the reaction; the stream of hydrogen
chloride should be regulated accordingly. The flask is removed
from time to time and weighed; when the absorption of gas
practically ceases, the increase in weight will be about 875 g.
(25 per cent more than the theoretical amount).

The product is now cooled, placed in a 4-l. beaker, and treated
with solid sodium carbonate until just alkaline to litmus.
Water is added from time to time, to facilitate the reaction
with the sodium carbonate and to prevent the separation of salt;
about 500 cc. are required. The mixture is transferred
to a separatory funnel and the aqueous layer separated.
The crude dichlorohydrin, which weighs 1250 g., is distilled in vacuo.
The first fraction boiling below 68'0/14 mm. weighs 225 g., and consists
of water and some dichlorohydrin; the dichlorohydrin is collected
between 68-75'0/14 mm., and weighs about 775 g. The water is separated
from the first fraction, which is then redistilled and yields 100 g.
of dichlorohydrin. A still further amount of material (40-45 g.)
may be obtained by extracting with benzene, the aqueous layer obtained
in the neutralization process. This is, however, hardly profitable.
The neutralization and distillation will require about four hours.

The 875 g. of dichlorohydrin thus obtained boils over a
7'0 range; this is 70 per cent of the theoretical amount.
Redistillation yields 700-720 g. boiling 70-73'0/14 mm.
(57 per cent of the theoretical amount).


2. Notes

The most convenient hydrogen chloride generator is that described
by Sweeney.[1] Concentrated hydrochloric acid is introduced
into concentrated sulfuric acid, by means of a dropping funnel
and a _capillary tube leading to the bottom of the sulfuric
acid container_. It is convenient to use a 3-l. bottle for this
container and a 1-l. funnel to contain the hydrochloric acid.
The gas is dried by passing through a wash-bottle containing
concentrated sulfuric acid. An empty catch-flask should be
connected between the generator and the absorption flask in case
any glycerol tends to suck back at the start of the reaction.
About 6 kg. of concentrated hydrochloric acid and 10 kg.
of concentrated sulfuric acid are required in one run.
The generating flask will have to be recharged every six hours;
it should be half filled with sulfuric acid. Aside from this,
the apparatus needs no attention. The oil bath can be conveniently
heated on an electric hot plate.

The dichlorohydrin boiling over a 7'0 range is sufficiently pure for
most purposes. It contains very little, if any, isomeric dichlorohydrin,
since on oxidation it gives dichloroacetone in good yields.


3. Other Methods of Preparation

The following methods of preparing dichlorohydrin are described
in the literature: the action of gaseous hydrogen chloride on
glycerol;[1b] the action of gaseous hydrogen chloride on glycerol
mixed with an equal volume of acetic acid;[2] the action of hydrogen
chloride gas on glycerol containing 1-2 per cent of some organic acid,
as acetic, as a catalyst;[3] the action of aqueous solution of
hydrochloric acid on glycerol containing acetic acid as a catalyst;[4]
the action of sulfur monochloride on glycerol.[5]

The previous work, described in the literature, indicated that the best
yields were obtained by the treatment of glycerol containing 1-2 per
cent of acetic acid as a catalyst by gaseous hydrogen chloride.
Therefore this method was employed.


[1a] J. Am. Chem. Soc. 39, 2187 (1917)

[1b] Ann. 88, 311 (1853); Ann. chim. phys. (3) 41, 297 (1854);
(6), 22, 437 (1891); Bull. soc. chim. (2), 48, 237
(1887); Z. physik. Chem. 92, 717 (1918); 93, 59 (1919); 94, 691
(1920); D. R P. 263,106; 272,337; Frdl. 11, 33 (1912).

[2] Ann. Spl. 1, 2I8 (1861); Ann. chim. phys. (3) 60, 18 (1860).

[3] D. R. P. 197,308; Frdl. 9, 33 (1908).

[4] D. R. P. 197,309; Frdl. 9, 33 (1903).

[5] Ann. 122, 73 (1862); 168, 43 (1873); Ber. 5, 354
(1872); Ann. chim. phys. (6) 22, 437 (1891).



IX

GLYCEROL a-MONOCHLOROHYDRIN

C3H5(OH)3 + HCl--> CH2ClCHOHCH2OH + H2O

Prepared by J. B. CONANT and O. R. QUAYLE. Checked by O. KAMM
and A. O. MATTHEWS.


1. Procedure

FIVE HUNDRED grams of glycerol (90 per cent) and 10 g.
of glacial acetic acid are mixed in a weighed 1-l. flask,
which is placed in an oil bath heated to 105-110'0. A rapid
stream of dry hydrogen chloride is introduced into the mixture.
The flask is removed from the bath from time to time and reweighed.
At the end of about four hours the flask will have gained 190 g.
in weight. The reaction is then complete.

The product is distilled under diminished pressure.
Below 114'0/14 mm., 220-250 g. distil; this portion is mostly water.
The monochlorohydrin is collected between 114-120'0/14 mm.;
it weighs 360 g., which is 66 per cent of the theoretical amount.
About 20 g. more may be obtained by neutralizing the first fraction
and separating the aqueous layer.


2. Notes

The same apparatus is employed as in the preparation of dichlorohydrin
(preparation VIII, p. 29).

The portion boiling 120-130'0/14 mm. only amounts to 15-30
g., showing that very little of the b-compound is formed.
This is further shown by the fact that the dichlorohydrin formed
by continued action of hydrogen chloride under the same conditions
contains very little, if any, a, b dichloride.

Two kilograms of concentrated sulfuric acid and 750 g.
of concentrated hydrochloric acid are sufficient to produce
the necessary amount of hydrogen chloride.

A light straw-colored final product is obtained in some cases.

An alternative procedure which is slower and gives slightly
lower yields, but does not require a hydrogen chloride generator,
is as follows:

Three hundred grams of glycerol, 600 cc. of hydrochloric acid
(sp. gr. 1.19) and 15 g. of glacial acetic acid are heated
under a reflux condenser for ten hours, in a 2-l. flask.
The boiling should be very gentle in the early stage of
the reaction, as considerable hydrochloric acid vapor is evolved.
As the reaction progresses, and the evolution of acid vapors diminishes,
the mixture is more strongly heated.

The reaction products are distilled under ordinary pressure until
the temperature of the liquid has reached 140'0 (thermometer bulb
immersed in the liquid). The residual products are distilled
under diminished pressure, and the following fractions obtained.
(1) Up to 115'0/11 mm.; (2) 115-117'0/ 11 mm.; (3) 117-170'0/11 mm.
(1) is mostly aqueous hydrochloric acid; (2) is the monochlorohydrin;
and (3) is glycerol. The second portion is redistilled and the portion
boiling at 115-118'0/11 mm. or 133-136'0/20 mm. is collected.
The yield is 190-205 g., 53-57 per cent of the theoretical amount.


3. Other Methods of Preparation

The following methods of preparing monochlorohydrin are described
in the literature: action on glycerol of gaseous hydrogen
chloride;[1] action of gaseous hydrogen chloride on glycerol
mixed with an equal volume of acetic acid;[2] action of aqueous
hydrochloric acid on glycerol[3] alone or with an organic acid
(1-2 per cent), such as acetic, as a catalyst;[4] gaseous hydrogen
chloride with an organic acid, as acetic, as a catalyst;[1b] gaseous
hydrogen chloride with the ester of an organic or inorganic acid
as a catalyst;[2b] the action of sulfur monochloride on glycerol.[3b]

[1] Ann. 88, 311 (1853); Ann. chim. phys. (3) 41, 297
(1834); V. R. P. 254,709; 269,657; Frdl. 11, 31 (1912).

[2] Ann. chim. phys. (3) 60, 18 (1860).

[3] D. R. P. 180,668; Frdl. 8, 27 (1907); J. Am. Chem. Soc. 42, 2096
(1920).

[4] D. R. P. 197,309; Frdl. 9, 34 (1908).

[1b] D. R. P. 197,308; Frdl. 9, 33 (1908).

[2b] D. R. P. Anm. 23,510; 16,579; Frdl. 9, 36 (1908).

[3b] D. R. P. 201,230; Frdl. 9, 35 (1908).



X

HYDRAZINE SULFATE

2 NH3 + NaOCl--> NH2NH2 + H2O + NaCl

Prepared by ROGER ADAMS and B. K. BROWN. Checked by J. B. CONANT
and W. L. HANAWAY.

1. Procedure

A NORMAL solution of sodium hypochlorite is prepared as follows:
in a 5-l. round-bottom flask are placed 1800 g. of sodium
hydroxide solution (300 g. of sodium hydroxide to 1500 g.
of water) and 1500 g. of ice. Chlorine gas is then passed into
the solution until it has gained in weight approximately 213 g.
During this addition, the solution must be kept thoroughly
cooled with ice, in order that chlorates will not be formed.
After all the chlorine has been passed in, it is necessary to be
certain that the mixture is slightly alkaline, since any excess
of free chlorine in the solution prevents the formation of hydrazine.

In a 14-inch evaporating dish are placed 1500 cc.
of c. p. ammonia water (sp. gr. 0.90), 900 cc. of distilled water,
375 cc. of 10 per cent gelatine solution, and 1200 cc.
of the normal sodium hypochlorite solution prepared as above.
This mixture is heated as rapidly as possible and boiled down
until one-third of the original volume is left. This solution
is then cooled thoroughly with ice and filtered with suction,
first through two layers of toweling and then through one
thickness of ordinary filter paper over cloth, in order to remove
finely divided solid impurities. The solution is then placed
in a precipitating jar, and cooled down thoroughly (0'0) with ice
and salt; 10 cc. of concentrated sulfuric acid for each 100 cc.
of solution are gradually added with constant stirring.
A precipitate of hydrazine sulfate (NH2NH2<.>H2SO4) forms.
The mixture is allowed to stand in the cold for a few hours in order
to complete the precipitation, and is then filtered by suction in the
usual way and washed with cold alcohol. The yield varies from 53 g.
to 58 g. per 1500 cc. of ammonia water (34-37 per cent of the
theoretical amount). The product is perfectly white and crystalline,
and satisfactory for almost any purpose. If an absolutely pure
product is desired, it must be recrystallized from water.
For every 21 g. of crude product, 100 g. of boiling water are used.
If the crude hydrazine is brown, it is advisable to use a little
bone-black. After the mixture has been filtered and cooled to 0'0, 19 g.
of pure white crystals are obtained.


2. Notes

In the preparation of the sodium hypochlorite solution it is quite
necessary that the mixture be kept cold and be alkaline to red
litmus paper at the end of the reaction, if good yields of hydrazine
are to be obtained.

Since iron is an anti-catalyzer, it is necesssary{sic} to use
distilled water throughout the process.

As a viscolizer, a substance such as starch, glycerol, glue or
gelatine may be used; the last, however, gives by far the
most satisfactory results.

In order to obtain a pure white hydrazine sulfate as the
first precipitate, it is necessary to cool the hydrazine solution
thoroughly and filter it twice before the sulfuric acid is added.
Moreover, the sulfuric acid must be added slowly and with stirring.
If these conditions are not followed, material containing
brown particles results.

The mother liquor obtained from the crystallized hydrazine
sulfate contains a small amount of hydrazine. If 200 g.
of copper sulfate are dissolved in water and added to 10 l.
of the filtrates from the above processes, a light-blue crystalline
precipitate of the double salt of copper sulfate and hydrazine
sulfate will be formed after ten hours. This salt, when suspended
in ten times its weight of distilled water and treated with hydrogen
sulfide, decomposes into copper sulfide and hydrazine sulfate.
After the copper salt has been filtered off, the solution
is concentrated until the hydrazine sulfate crystallizes.
The yield of product is small, so that it is hardly advisable
to undertake this recovery in the laboratory.

It is possible for one man, simultaneously evaporating six dishes
of the hydrazine mixture, to turn out from 20 to 25 runs in nine hours.
The time for the evaporation of a solution, such as is mentioned
in the experimental part, with a four-flame Bunsen burner, is two to
three hours; if the evaporation is carried out more slowly than this,
the yield of product is distinctly diminished.


3. Other Methods of Preparation

Hydrazine salts have been prepared by the action of hypochlorites on
ammonia[1] or urea;[2] by the hydrolysis of salts of sulfohydrazimethylene
disulfonic acid;[3] by the hydrolysis of triazoacetic acid;[4] by the
reduction of diazoacetic ester;[5] by the reduction of nitroguanidine
followed by hydrolysis;[6] by the reduction of the nitroso derivatives
of hexamethylene tetramine;[7] by the reduction of nitrates or nitrites
with zinc in neutral solution;[8] by the action of sodium bisulfite
on hyponitrous acid followed by reduction;[1b] by the reduction
of K2SO3N2O2;[2b] by the action of ammonia on dichlorourea;[3b]
by the reduction of nitrosoparaldimin;[4b] by the action of copper
sulfate on ammonia at high temperatures;[5b] by the reduction of
methylene diisonitrosoamine;[6b] by the hydrolysis of the addition
product of diazoacetic ester and fumaric or cinnamic esters.[7b]


[1] D. R. P. 192,783; Chem. Zentr. 1908 (I), 427; Chem. Ztg. 31, 926
(1907); D. R. P. 198,307; Chem. Zentr. 1908 (I), 1957; Eng. Pat.
22,957; C. A. 2, 1999 (1908); U. S. Pat. 910,858; C. A. 3, 1065
(1909); French Pat. 382,357; C. A. 3, 2358 (1909); Ber.
40, 4588 (1907); Laboratory Manual of Inorganic Preparations,
by A. B. Lamb, Harvard University, Cambridge, Mass.

[2] J. Russ. Phys. Chem. Soc. 37, 1 (1905); Chem. Zentr. 1905
(I) 1227; D. R. P. 164,755; Frdl. 8, 53 (1905); French Pat. 329,430;
J. Soc. Chem. Ind. 22, 1063 (1903); Chem. Zentr. 1905 (I) 1227.

[3] D. R. P. 79,885; Frdl. 4, 26 (1895); Ber. 28, 2381 (1895).

[4] Ber. 20, 1632 (1887); Chem. News 55, 288 (1887); D. R. P. 47,600;
Frdl. 2, 554 (1889); J. prakt. Chem. (2) 39, 27 (1889).

[5] Ber. 27, 775 (1894); 28, 1848 (1895); D. R. P. 58,751; Frdl. 3, 16
(1891); D. R. P. 87,131; Frdl. 4, 28 (1896).

[6] Ann. 270, 31 (1892); D. R. P. 59,241; Frdl. 3, 16
(1891); Eng. Pat. 6,786; J. Soc. Chem. Ind. 11, 370 (1892).

[7] D. R. P. 80,466; Frdl. 4, 27 (1895); Ann. 288, 232 (1895).

[8] Eng. Pat. 11, 216; J. Soc. Chem. Ind. 14, 595 (1895). [1b] Ber.
33, 2115 (1900); Ann. 288, 301 (1895).

[2b] Ber. 27, 3498 (1894).

[3b] J. Chem. Soc. 95, 235 (1909); Chem. News 98, 166 (1908).

[4b] Ber. 23, 752 (1890).

[5b] Chem. News 66, 223 (1892).

[6b] Ber. 27, 3292 (1894);

[7b] Ber. 21, 2637 (1888).



XI

MESITYLENE

3 CH3COCH3 + (H2SO4)--> C6H3(CH3)3 +3H2O

Prepared by ROGER ADAMS and R. W. HUFFERD. Checked by H. T. CLARKE
and W. W. HARTMAN.

1. Procedure

IN a 12-l. round-bottom flask, arranged so that the contents
can be mechanically stirred, are placed 4600 g. (5750 cc.)
of technical acetone. The flask is then well cooled with an
ice-and-salt mixture, until the temperature of the acetone
is between 0'0 and 5'0. Stirring is started, and 4160 cc.
of commercial concentrated sulfuric acid is run in at such a rate
that the temperature of the mixture never rises above about 10'0.
This addition is accomplished in about five to ten hours.
The stirring is continued for three to four hours longer,
while the flask still remains immersed in the original
freezing mixture to which no further amount of ice is added.
The mixture is then allowed to stand at room temperature for eighteen
to twenty-four hours.

A 5-l. round-bottom flask is fitted with a rubber stopper or a cork
stopper coated with pitch, carrying two glass tubes, one of which
(for the entrance of steam) reaches to the bottom of the flask,
while the other extends into the open end of a condenser set for
downward distillation. The stopper should be wired into the flask.
The glass delivery tube into the condenser should not be less than a
12-mm. bore, and the condenser should consist of two 120-cm. water-cooled
condensers attached end to end. To the end of the condensing system,
an adapter is attached, the small end of which is at least 8 mm.
in bore and is fitted tightly into a stopper in a 2-l. suction flask.
To the side-arm of the suction flask is attached a tube leading to an
exhaust fan, in order to carry away the gases which are evolved during
the subsequent distillation. In the 5-l. flask are placed about 2 l.
of the sulfuric acid-acetone reaction mixture, and the flask
is then heated with a free flame and shaken occasionally.
A reaction starts at the end of about fifteen or twenty minutes,
as shown by the evolution of gas (chiefly sulfur dioxide), and is
allowed to run for about three minutes. At the end of this time,
a current of steam is passed in and continued for about three minutes.
During this period a large proportion of the mesitylene distils
and should be kept separate from the subsequent distillate.
The steam distillation is continued at such a rate that about 800 cc.
distils in twenty-five to thirty minutes and is collected as a
second distillate. At the end of this time, the distillation
is stopped, the water poured off from the distilling flask
and the tarry material emptied out while hot into waste jars.
The total amount of original reaction mixture requires
five distillations similar to the one just described.
The first distillates from each of the five distillations are mixed,
and the layer of mesitylene is separated from the water.
This is shaken with sodium hydroxide solution until no more odor of sulfur
dioxide is noticeable, then washed twice with water and distilled.
The first portion of the distillate consists of a small amount of water
and mesitylene and is added to the combined second distillates.
The fraction which distils up to 210'0 is saved. The second distillates
are combined, washed in the same way as the first and then distilled;
the fraction which distils up to 210'0 is combined with the corresponding
fraction from the first distillates.

These combined fractions (which boil up to 210'0) and 15 g.
of sodium are placed in a 2-l. distilling flask, the side-arm of
which is closed with a rubber tube and pinchcock and which is fitted
with a reflux condenser. The mixture is heated just below the boiling
point for about three hours, during which time the impurities are
attacked by the molten sodium, and a gelatinous, reddish mass forms.
The reflux condenser is now removed and one set for downward
distillation is attached to the side-arm. The mixture is distilled
and about two-thirds of the liquid removed in this way.
The residue is cooled, the liquid poured off from solid material
and distilled up to 210'0.

The distillates from the sodium treatment are now fractionated with
a good column (at least 30 cm. long), and the portion which boils
at 163-167'0 is collected. The yield of this fraction varies in
different runs from 430 to 470 g. (13-15 per cent of the theoretical
amount), but very often will be as high as 500 g., and has reached,
in certain experiments, 600 g.

An alternative method for the purification of the crude material
has been employed by Clarke and Hartman, and yields a slightly
higher-grade product than the sodium method. It is as follows:

The combined distillates are treated with an equal volume of concentrated
sulfuric acid and the solution warmed on a water bath for an hour,
under a reflux condenser, with occasional shaking or, better, with
mechanical stirring. Upon cooling, mesitylene sulfonic acid crystallizes
and the unsulfonated material remains as an oil on the surface.
The mixture is filtered through flannel or a "filtrose" plate,
and the crystals are washed with 60-70 per cent sulfuric acid.
The oily layer is again warmed with sulfuric acid, as before.
The acid and oily filtrates from the two sulfuric acid treatments are steam
distilled, and the distillate combined with the next batch of material.
The crystals are mixed with 2 l. of 15 per cent hydrochloric
acid and heated under a reflux condenser for two to three hours.
The reaction mixture is now steam distilled, the mesitylene separated,
dried over calcium chloride and fractionated; the portion which boils
at 163-167'0 is collected.

2. Notes

The cooling of the reaction flask must be very efficient, a 10-15 cm.
blanket of a thorough mixture of ice and salt being used.
If this precaution is not employed, the time for the addition
of the sulfuric acid is greatly increased, provided the temperature
of the reaction mixture is still kept within the limits mentioned.

If a cork is used for the steam distillation of the reaction mixture
of acetone and sulfuric acid, it should be coated well with pitch and wired
into the flask. This is necessary because the vapors of the reaction
mixture attack an ordinary cork very badly, and soften it so much
that it is necessary to rewire it to prevent it from slipping out.
A rubber stopper is satisfactory and may be used in several runs.

The evolution of gas is so vigorous that it is not possible to distil
more than 2 l. of the original reaction mixture at one time
in the apparatus described. The connections on the apparatus,
in which the mesitylene is obtained from the crude reaction mixture,
should be tight, since the fumes evolved during the heating
are very irritating.

The product which distils during the initial heating and the three
minutes of steam distillation is mainly satisfactory material; the rest
of the steam distillation yields only a small amount of pure product.
The two portions of the distillate are, therefore, kept separate,
since the second distillate always contains a considerable amount
of high-boiling product which tends to cause emulsification of
the alkali in the purification. No recovery of acetone is made.

The mechanism of the reaction is undoubtedly as follows:
when the sulfuric acid and acetone are in contact for long periods
of time, several molecules of the acetone condense to form aldol
condensation products. These do not break down into mesitylene until
the temperature is raised in the second part of the experiment.

While the original reaction mixture is standing, the temperature
gradually rises to 40'0 or 50'0 in the course of six to ten hours,
and then gradually cools off again. It is probable that at the end
of this time (when the flask has cooled again) the reaction mixture
could be distilled with nearly as good a yield as is obtained
after standing eighteen to twenty-four hours.

The wide variation in yields which are mentioned in the experimental
part is probably due to a slight change in the grade of the chemicals
which are used in this preparation. 3. Other Methods of Preparation

The cheapest and most convenient method by which mesitylene may
be prepared is by the action of a dehydrating agent upon acetone;
the agent most commonly used is sulfuric acid.[1] It has been shown
also that phosphoric acid will convert acetone to mesitylene.[2] A number
of other methods have also been used for the preparation of mesitylene:
the action of sulfuric acid on methyl acetylene;[3] the action
of sulfuric acid on mesityl oxide and phorone;[4] the action of
aluminium{sic(british)} chloride on methyl chloride and benzene;[5]
the action of mineral acids upon mesitoyl or benzoyl mesitylene;[6]
the action of phosphoric acid upon diaceto-mesitylene;[7] the treatment
of methylene-3-dimethyl-1, 5-cyclo-hexene-1 with bromine and then
with alcoholic potash.[8]

[1] Ann. 141, 131 (1867); 147, 43 (1868); 278, 210 (1893); Bud.
soc. chim. (2) 40, 267 (1883); J. prakt. Chem. (1) 15, 129
(1838); Am. Chem. J. 15, 256 (1893); 20, 807 (1898).

[2] J Chem. Soc. 99, 1251 (1911).

[3] Ber. 8, 17 (1875).

[4] Ber. 7, 1169 (1874); 10, 858 (1877).

[5] Ber. 12, 329 (1879); Ann. chim. phys. (6) 1, 461 (1884).

[6] Ber. 32, 1910 (1899).

[7] Ber. 32, 1563 (1899).

[8] Ber. 43, 3093 (1910).



XII

METHYL RED

(_o_)HO2CC6H>4s>NH2 + HNO2 + HCl-->(_ o_)HO2CC6H4N2Cl + H2O
(_o_) HO2CC6H4N2Cl + C6H5N(CH3)2-->(_ o_)HO2CC6H4N = NC6H4N(CH3)2 + HCl

Prepared by H. T. CLARKE and W. R. KIRNER. Checked by ROGER ADAMS
and J. B. DAVIS.

1. Procedure

TECHNICAL anthranilic acid (generally about 95 per cent pure)
(685 g.) is dissolved in 1.5 l. of water and 500 cc.
of concentrated hydrochloric acid (sp. gr. 1.17), by heating.
The insoluble dark impurity present in small amounts is filtered off,
and the filtrate is transferred to a 10-l. crock and chilled
with stirring. It is then mixed with a mush of 2.5 kg.
of ice and 750 cc. of concentrated hydrochloric acid. The crock
is cooled externally with ice, and the contents stirred continuously.
When the temperature reaches about 3'0, a filtered solution of 360 g.
of sodium nitrite in 700 cc. of water is dropped in slowly,
through a long capillary tube reaching below the surface
of the liquid, until a faint but permanent reaction to starch
potassium iodide paper is obtained; the temperature is kept
between 3'0 and 5'0. This operation requires all but about 30 cc.
of the nitrite solution and occupies one and a half to two hours.
To the solution of the diazonium salt are now added 848 g.
of dimethylaniline; this may be done rapidly, as the temperature
does not rise appreciably. Stirring is continued for one hour,
the temperature being kept at 5'0 Five hundred cc. of a filtered
solution of 680 g. of crystallized sodium acetate diluted to 1200 cc.
are then added, and the stirring continued for four hours.
If a foamy solid rises to the surface during this time and refuses
to become incorporated by the stirrer, a few drops of ethyl acetate may
be added to reduce the foam. The mixture is allowed to stand overnight
in an ice bath which is well insulated by several thicknesses of burlap;
the temperature must be kept below 7'0 to get a good yield of product.
The remainder of the sodium acetate solution is then added
with stirring, and after the mixture has been stirred for an
additional period of one to three hours, the temperature is allowed
to rise slowly to 20-25'0 in the course of twenty-four hours.
Just enough sodium hydroxide solution is then added, with stirring,
to cause the mixture to have a distinct odor of dimethylaniline
(about 240 cc. of a 40 per cent solution are generally required),
and the mixture is allowed to stand for forty-eight hours or longer
at room temperature (20-25'0).

The solid is then filtered off, washed first with water, then with 400 cc.
of 10 per cent acetic acid (to remove the dimethylaniline) and finally
with distilled water. The last filtrate is generally pale pink.
The solid is sucked as dry as possible, spread out on a tray in order
to allow most of the water to evaporate (fifteen to twenty hours)
and then suspended in 4 l. of methyl alcohol in a 12-l. flask.
This mixture is stirred on the steam bath under a reflux condenser
for one to two hours, allowed to cool slowly, and then chilled in an ice
bath and filtered. The solid product is washed with a second 4 l.
of cold methyl alcohol. After being dried in air, the product
varies in weight from 820 to 870 g.

The product is extracted with boiling toluene in the following manner:
150 g. are placed in a fluted filter paper of 29 cm.
diameter in a 25-cm. glass funnel which passes through the cork
of a 2-l. flat-bottom conical flask containing 1250 cc.
of toluene (Fig. 2). The flask is heated on an electric stove,
and a 12-l. round-bottom flask is placed on the funnel to act
as a condenser, cold water being run through the flask.
The toluene is boiled until the condensed liquid runs through
almost colorless (this requires from four to ten hours). The heating
is then discontinued, and, as soon as the liquid ceases to boil,
the flask is removed to a bath containing water at 90-100'0;
the level of the water should be slightly above the level
of the liquid in the flask. This arrangement permits the
temperature to fall slowly so that large crystals are obtained.
In the meantime a second conical flask containing 1250 cc.
of toluene is attached to the funnel, and a new charge of 150 g.
of crude methyl red is placed in the paper. When extraction
is complete it is found that a certain amount of black amorphous
insoluble matter remains on the filter; this is discarded.
The crystals of methyl red are filtered off and washed with a
little toluene. The weight of pure material is 755-805 g.
The mother liquors are concentrated to one-fourth of their volume,
and the crystals which separate on cooling are recrystallized
from fresh toluene. The recovered toluene can, of course,
be employed again. The total yield of pure methyl red is 790--840 g.
It melts at 181-182'0.

The watery mother liquors from the crude methyl red are rendered
alkaline with sodium hydroxide and distilled until no more
dimethylaniline passes over. In this way 250 to 400 g.
of moist dimethylaniline are recovered.


2. Notes

The amount of hydrochloric acid indicated must not be reduced;
otherwise, diazoamino compounds are formed.

It is essential to keep the temperature low while unreacted diazobenzoic
acid remains in solution, in order to avoid decomposition.
If this precaution is not taken, the yields are considerably diminished,
through the formation of tarry by-products.

The use of a capillary tube for the addition of sodium nitrite
prevents loss of nitrous acid by local reaction at the surface
of the acid solution. The tube should not be tightly connected
to the dropping funnel, but should be so arranged that air is sucked
through with every drop. In this way, the entrance of the acid
liquor into the capillary is prevented.

The formation of the azo compound takes place slowly on the addition
of the dimethylaniline, but the speed of the reaction is greatly
increased when the hydrogen ion concentration is lowered
by the addition of the sodium acetate. It is nevertheless
necessary to allow the reaction mixture to stand a long time;
if the product be filtered off after only twenty-four hours,
a further quantity of dye will separate from the filtrate on standing.
The hydrochloride of methyl red is only sparingly soluble in
cold water, and is apt to separate in blue needles if the acidity
is not sufficiently reduced.

The alcoholic filtrate, obtained on digesting and washing the crude
methyl red, contains a more soluble red by-product which gives
a brownish-yellow solution in alkali. The methyl alcohol may be
recovered with very little loss by distillation; it is, however,
impracticable to attempt to recover any methyl red from the residue,
owing to the tarry nature of the by-product. The proportion of this
by-product is greatly increased if the temperature of the mixture
is allowed to rise too soon after the addition of the sodium acetate.

Methyl red is described as crystallizing in needles from glacial
acetic acid; on recrystallization from toluene it separates in plates.

When the methyl red is crystallized from toluene, it sometimes
separates in the form of bright-red lumps, probably on account
of too rapid crystallization. Under these conditions it is advisable
to crystallize again, using a somewhat larger amount of toluene.

It is advisable to titrate the crude anthranilic acid with standard
alkali and phenolphthalein before starting the experiment.
In checking these directions, an 80 per cent anthranilic acid
was used; it gave a correspondingly lower yield of methyl red
(650-700 g.). The yield of methyl red is about 65 to 70 per cent
based on the dimethylaniline actually used up, but only 58-63 per
cent based on the anthranilic acid actually present in the technical
anthranilic acid employed.


3. Other Methods of Preparation

Methyl red was first prepared[1] by diazotization of anthranilic
acid in alcoholic solution, the product being allowed to react with
dimethylaniline in the same solvent. It has been stated[2] that this
process does not work satisfactorily and yields a different product,
of brownish-red color.

The preparation of methyl red in aqueous solution has been
described by two workers, one of whom[3] gives but few details
and claims a nearly quantitative yield; the other[4] gives fuller
details and states the yield to be 43.1 per cent of the theory.
The recrystallization of methyl red from toluene is stated[5]
to yield a product melting at 183'0.

[1] Ber. 41, 3905 (1908).

[2] Chem. Zentr. 1910, (1), 960; 1910, (11), 1561.

[3] J. Chem. Soc. 97, 2485 (1910).

[4] C. A. 14, 3406 (1920)

[5] J. Chem. Soc. 99, 1334 (1911).



XIII

_p_-NITROBENZOIC ACID

(_p_)NO2C6H4CH>3s> + 3O(Na2Cr2O7 + H2SO4)--> (_p_)NO2C6H4CO2H + 3H2O

Prepared by O. KAMM and A. O. MATTHEWS. Checked by H. T. CLARKE
and W. W. HARTMAN.

1. Procedure

IN a 5-l. round-bottom flask, fitted with a mechanical stirrer,
are placed 680 g. of sodium dichromate, 1500 cc. of water,
and 230 g. of _p_-nitrotoluene. Stirring is started, and 1700 g.
of concentrated sulfuric acid are allowed to flow in during about
thirty minutes. The heat of dilution of the sulfuric acid will cause
the nitrotoluene to melt, and rapid oxidation will soon take place.
The last half of the sulfuric acid must be added gradually,
in order to prevent too violent a reaction. Since a small amount
of nitrotoluene is volatilized, it is advisable to carry on this
work under a hood.

After the sulfuric acid has been added and the spontaneous heating
of the reaction mixture has subsided, the mixture is heated to gentle
boiling for about half an hour. After the reaction mixture has cooled,
2 l. of water are added, the cooled solution is filtered through
a cloth filter, and the product washed with about 1 l. of water.
In order to remove the chromium salts as completely as possible,
the crude nitrobenzoic acid is warmed on the water bath and agitated
with 1 l. of dilute (5 per cent) sulfuric acid solution.
After cooling, the product is again filtered. It is then dissolved
in 5 per cent sodium hydroxide solution, filtered from any chromium
hydroxide remaining, and also from unchanged nitrotoluene.
The filtrate, which should be light yellow or greenish in color,
is acidified with dilute sulfuric acid, with stirring.
It is usually preferable to run the alkaline solution into
the dilute sulfuric acid, rather than to use the reverse procedure,
for the precipitation of the nitro acid. The precipitated product
is filtered with suction, washed thoroughly, and dried. The product
should possess only a light-lemon color. The yield should be 230-240 g.
(80-85 per cent of the theoretical amount).

For a product of special purity, crystallization from benzene
is advisable. For most purposes, however, the nitrobenzoic acid
may be used without crystallization, since its melting point is found
to be within 2'0 of the correct value of 238'0.


2. Notes

The above procedure differs from that recorded in the literature,
mainly in the use of a fairly large excess of sulfuric acid.
This shortens the reaction time from forty hours to about one hour,
which is especially convenient in the preparation of the acid
on a laboratory scale. Because of the use of this large
excess of sulfuric acid, the reaction is apt to be rather
violent if the directions given are not carefully followed.
The oxidation should be carried out under a hood. Small amounts of
nitrotoluene are lost by volatilization, but this loss is not serious,
as can be seen from the yield of product obtained.

Ten or 20 g. of unchanged nitrotoluene can be recovered from
the reaction mixture by steam distillation, but the value of
the by-product would not pay for the time spent in recovery.

The washing of the crude reaction product with dilute sulfuric acid
is advisable, if good material is to be obtained. If an efficient
centrifuge is available for use at this stage of the operation,
this separate washing may prove to be less essential.

When a sparingly soluble organic acid is precipitated from
fairly concentrated solution, the precipitate is liable
to carry down with it some of the salt of the organic acid.
Addition of the salt solution to the mineral acid, with stirring,
avoids this difficulty. 3. Other Methods of Preparation

The nitration of benzoic acid produces only very small yields
of the _p_-nitro product.[1] The only practical method for the
preparation consists in the oxidation of _p_-nitrotoluene, although
for this purpose various oxidizing agents are used. In addition
to nitrotoluene, _p_-nitrobenzyl alcohol, _p_-nitrocinnamic acid
and similar compounds may be oxidized, but their cost is prohibitive
in comparison with that of the cheaper nitro hydrocarbon.

_p_-Nitrotoluene may be oxidized by means of strong nitric acid,[2]
chromic acid mixture,[3] or permanganates.[4] Electrolytic
oxidation[5] has also been proposed. The procedure given above
involves the use of chromic acid mixture, but, owing to a change
in the concentration of sulfuric acid, the time of reaction is greatly
shortened and the preparation is thus considerably improved.

[1] Ber. 8, 528, 536 (1875)

[2] Ann. 127, 137 (1863); 128, 257 (1863)

[3] Ann. 139, 335 (1866).

[4] J. Am. Chem. Soc. 41, 1575 (1919).

[5] R. P. 117, 129; Frdl. 6, 112.



XIV _ p_-NITROBENZYL CYANIDE

C6H5CH2CN + HNO3--> (_p_)NO2C6H4CH2CN + H2O

Prepared by G. R. ROBERTSON. Checked by ROGER ADAMS and H. O. CALVERY.

1. Procedure

IN a 2-l. round-bottom flask, fitted with a stopper holding a dropping
funnel and a mechanical stirrer, is placed a mixture of 275 cc.
of concentrated nitric acid (sp. gr. 1.42) and 275 cc.
of concentrated sulfuric acid (sp. gr. 1.84). This is cooled to 10'0
in a freezing mixture, and 100 g. of benzyl cyanide (free from alcohol
and water) are run in slowly, at such a rate that the temperature
remains at about 10'0 and does not exceed 20'0. After all the benzyl
cyanide has been added (about one hour), the ice bath is removed,
the mixture is stirred for an hour and then poured on to 1200 g.
of crushed ice. A pasty mass slowly separates; more than half
of this mass is _p_-nitrobenzyl cyanide, the other constituents
being _o_-nitrobenzyl cyanide, and a variable amount of an oil
which resists hydrolysis; apparently no dinitro compounds are formed.
The mass is filtered on a porcelain funnel with suction, pressed well
to remove as much oil as possible, and dissolved in 500 cc.
of boiling alcohol (95 per cent). On cooling, _p_-nitrobenzyl
cyanide crystallizes; the mother liquor, on distillation,
gives an impure alcohol which can be used for the next run.
Recrystallization from 550 cc. of 80 per cent alcohol (sp. gr.
0.86 to 0.87) yields 70 to 75 g. (50-54 per cent) of a product
which melts at 115-116'0.

This product is satisfactory for most purposes, and incidentally
for the preparation of _p_-nitrophenylacetic acid. Occasionally
it must be free even from traces of the ortho compound,
and in this case should be crystallized again from 80 per cent alcohol;
it then melts at 116-117'0.


2. Notes

Fuming nitric acid may be used in nitrating benzyl cyanide,
but the method here described is cheaper.

The yield of 70 g. is obtained from benzyl cyanide, which boils
over a 5'0 range prepared as described in preparation III
(p. 9). Very pure benzyl cyanide will give a slightly higher yield,
while commercial grades may give only 50 g. of _p_-nitrobenzyl
cyanide and much oil.

The reaction has been also carried out with 500 g.
of benzyl cyanide. Under these conditions a 5-l. flask was used,
and it required two and a half hours to add the benzyl cyanide.
The yield of product was 325 to 370 g.


3. Other Methods of Preparation

Nitrobenzyl cyanide has hitherto been prepared by the action
of fuming nitric acid[1] on benzyl cyanide.

[1] Ber. 17, 505 (1884); 33, 170 (1900); J. Biol. Chem. 39, 585
(1919); J. Am. Chem. Soc. 43, 180 (1921).



XV

_p_-NITROPHENYLACETIC ACID

(_p_)NO2C6H4CN + H2SO4 + 2H2O--> (_p_)NO2C6H4CH2CO2H + NH4HSO4

Prepared by G. R. ROBERTSON. Checked by ROGER ADAMS and H. O. CALVERY.

1. Procedure

IN a 1-l. round-bottom flask are placed 100 g. of _p_-nitrobenzyl
cyanide. A solution of 300 cc. of concentrated sulfuric acid
(sp. gr. 1.84) in 280 cc. of water is prepared, and two-thirds
of this solution is poured on to the _p_-nitrobenzyl cyanide.
The mixture is shaken well, until the solid is all moistened
with the acid. Any solid material sticking to the walls of
the vessel is now washed down into the liquid with the remainder
of the acid, the flask is attached to a reflux condenser, then set,
without shaking, over a 10-cm. hole in a large sheet of asbestos
board which rests on a tripod, and heated until the mixture boils.
The boiling is continued for fifteen minutes.

The reaction mixture, which becomes rather dark, is diluted
with an equal volume of cold water and cooled to 0'0 or below.
The solution is filtered, the precipitate is washed several times
with ice water and then dissolved in 1600 cc. of boiling water.
(A few grams of animal charcoal are added in dissolving the precipitate,
if a technical _p_-nitrobenzyl cyanide has been used.)
This solution is filtered as rapidly as possible through a large
folded filter, preferably with a steam funnel. In spite of
all precautions, however, some solid usually separates on the filter.
This must be redissolved in a minimum quantity of boiling water,
and this solution then filtered into the main solution.
The _p_-nitrophenylacetic acid separates in long, pale-yellow needles,
which melt at 151-152'0. The yield is 103 to 106 g.
(92- 3 per cent of the theoretical amount).


2. Notes

If the flask is not protected with an asbestos board or the equivalent,
decomposition occurs where the substance is super-heated on the side
walls of the flask. If crystals of the cyanide are allowed to remain
on the upper walls of the flask, they are not easily washed down
and so are not hydrolyzed.

The solubility curve of _p_-nitrophenylacetic acid is very steep
at temperatures near 100'0, so that the filtering of the boiling
solution should be rapid.

If a good grade of cyanide be used, it is not necessary to add
bone-black in order to obtain the acid in a pure state.

In making experiments with 500 g. of _p_-nitrobenzyl cyanide,
it was found that the time for hydrolysis was about the same as
when smaller amounts were used.


3. Other Methods of Preparation

_p_-Nitrophenylacetic acid has been formed by the nitration of
phenylacetic acid;[1] by the hydrolysis of its ester[2] or its amid,[3]
and by the hydrolysis of its nitrile with hydrochloric acid.[4]

[1] Ber. 42, 3596 (1909).

[2] Ber. 12, 1765 (1879).

[3] Ber. 14, 2342 (1881).

[4] Ber. 15, 834 (1882).




XVI

NITROSO-b-NAPHTHOL

C10H7OH(b) + HNO2--> C10H6(OH)NO(1,2) + H2O

Prepared by C. S. MARVEL and P. K. PORTER. Checked by H. T. CLARKE
and W. W. HARTMAN.

1. Procedure

IN a 12-l. round-bottom flask fitted with a mechanical stirrer are placed
500 g. of technical b-naphthol dissolved in a warm solution of 140 g.
of sodium hydroxide in 6 l. of water. The solution is cooled
to 0'0 in an ice-and-salt bath, and 250 g. of powdered technical
sodium nitrite is added. Stirring is started and 1100 g.
of sulfuric acid (sp. gr. 1.32) are added from a dropping funnel,
at such a rate that the whole is added in one to one and a half hours,
the temperature being kept at 0'0. During the reaction crushed ice
is added from time to time to maintain the temperature at 0'0;
about 1 kg. is usually used. After all of the sulfuric acid
has been added, the solution should react acid to Congo paper.
The mixture is stirred one hour longer at the low temperature
and then the nitroso-b-naphthol, which has gradually separated out
during the reaction, is filtered with suction and washed thoroughly
with water. The product is at first light yellow in color,
but after three to four days it gradually changes to a dark brown.
The moisture content seems to have some effect on the color.
After the product has been air-dried for about four days, the yield
is about 665 g.; it melts at 97'0. A sample of this partially
dried product, on drying _in vacuo_ over sulfuric acid for twenty hours,
loses about 10 per cent of its weight and the melting point is 106'0.
By longer drying under ordinary conditions, the melting point of 106'0
is reached. The total yield of dry product is about 595 g.
(99 per cent of the theoretical amount).

This product is satisfactory for all purposes. It may be obtained
in a crystalline condition, however, by recrystallizing from hot ligroin
(sp. gr. 0.71-0.72). About 2 g. of nitroso-b-naphthol will dissolve
in 15 cc. of boiling ligroin. The product is not very soluble
in cold ligroin, so that nearly all is recovered.


2. Notes

It is very necessary to keep the temperature near 0'0 while
adding the sulfuric acid, or a tarry product will be obtained.
Vigorous stirring and the addition of the sulfuric acid at the proper
rate are essential for a good product.

A large vessel is needed for the reaction, as the nitroso-b-naphthol
separates in a finely divided condition and there is some
tendency to foam.

The final air-dried product is pure except for its moisture content,
as is shown by the fact that on drying _in vacuo_ it has a very good
melting point. A sample of Kahlbaum's nitroso-b-naphthol melted
at 101--105.


3. Other Methods of Preparation


 


Back to Full Books